Category: Install

How to Install and More !

Boat Lettering and Graphics in Pinellas County, Florida Designed and Installed by the Boat Name Guy

Boat Name Guy has Your Boat Name Designed and Installed in Pinellas County 

The Boat Name Guy is a fast acting, creative one stop shop for boat name lettering, logos and registration numbers. The Boat Name Guy (B.N.G.) also produces a large range of marine identity personalization products.

Custom made signs, flags, Marine ID-Cards, License plates and apparel.

From the proofing to the installation and or shipping, Boat Name Guy will make your boat name experience a breeze. B.N.G. takes your boat name serious and will continue the momentum until you are 100% satisfied. You will remember the Boat Name Guy for his professionalism and speedy attention to the details that go behind into a boat name theme Identity.

Boat Names in Pinellas County

Boat Name Guy Has You Covered In Pinellas County, Florida

B.N.G. has always admired the Pinellas County area as one of the largest boat community’s in the world.  An area like this needed a dedicated boat name designer that is NOT also busy with other lines of work in the sign industry.  With so many sign companies saying they will get back to you, but never do… Websites that claim they have a large design team crew that always comes up short on their design ideas.

Not to mention the websites that offer the customer to design it themselves with a limited resource of fonts and graphics. With the hundreds of marinas, lagoons and boat sale showrooms there had to be someone that a boat owner could rely on.

Boat Name Guy can help you as soon as you are ready to make a name for your boat. With the easy Boat Identity Form you can have a response quickly and affordable. No job is too small, whether it is a dingy in Largo or a 63’ Yacht in Tarpon Springs. B.N.G will be there to help you! If your boat is in the water at Shell Key in Tierra Verde Pinellas County, or on a trailer on the Dunedin Causeway. Boat Name Guy has you covered!

The Boat Name Guy can also deliver or ship your graphics anywhere in the world with complete and accurate boat name installation instructions. B.N.G also has step by step tutorials on Youtube for a better visual understanding of the whole boat name process.

Boat Name Installation instructions

Doing Your Boat Name Yourself Can Be Easy

Weather you buy your boat name through a online sign shop or your local sign guy. It should be close to the same material.

You want to make sure who ever prints your graphics they are using the correct material that will sustain under harsh outside elements.

There is a difference!

A 3 year calendared, Averey vinyl will not last as long as an 8 year, 3M premium vinyl. They will both look the same when you first apply it, but after a few years you will see your graphics shrink up to a half inch or more. If when you are installing and you need to pop any persistent holes… Those pin point holes will open up. That is why it is important NOT to pop any bubbles for the first week.

Make sure you have all the tools you will need before you start the install.

You will need the following:
Acetone or Ammonia, Rapid Tac Installation Spray Liquid, and a Squeegee.
Application should not be attempted if temperature is below 55° Fahrenheit. Or hotter than 80 ° Fahrenheit.  Also a windy day is not recommended.
The area must be cleaned using Acetone to remove all wax and dirt.

Your Boat Name Installation Instructions:

1. Once area has been cleaned use the Rapid Tac Spray (shake well before use) and generously spray the area where the lettering is to be applied.  Do not wipe off this solution.

2. Place the lettering face down on a clean, flat surface.  Peel away the protective wax paper backing.  The lettering will remain adhered to the application tape with the sticky side of the lettering now exposed.  Be very careful not to allow the lettering to flip over onto itself as this will cause your sign to be damaged. Generously spray the sticky side of the lettering with the Rapid Tac spray this will stop the lettering from sticking.

3. While the area is still wet, place the lettering in the desired location. The Rapid Tac spray will allow you to move the lettering around until you get it into place.

4. Starting from the center, using the squeegee provided, gently rub the lettering from the center out and in all directions. Continue to squeegee until all liquid and air is removed from underneath lettering.

5. Wait 1 minute and spray the Rapid Tac over the application tape and squeegee again. Allow lettering to dry completely (approx. 30 minutes).

6. Slowly peel off the translucent application tape starting from the upper corner and pull down at a angle. The vinyl lettering will stay adhered to the surface. Note: If the lettering is not sticking to surface, repeat the squeegee process and let dry longer.

If you don’t think that these boat name installation instructions are easy it is OK! I can help you with any part of these instructions. Please contact me if you have any questions or if you would like me to come out and install for you.

HINTS:

*Easy-Off oven cleaner removes old painted letters, followed by white vinegar to remove any yellowing.
*Heat gun and a rubber scraper removes old vinyl letters.
*Any leftover air bubbles may be remedied by exposure to the sun, and if not they can be popped with a pin

Boat Names in the Tampabay/Clearwater Area

Doug Rohloff from Dunedin, Florida has been producing boat names in the Tampabay/Clearwater are for over 15 years.

Doug the “boat name guy” will help you design your unique boat name. Just tell him the name, style, size and how big. The brand boat and the size of the boat.

The boat name guy will come out to look at your boat, take measurements and photographs of where you would like the boat name. He will then design proofs to give you ideas of how you dreamed the boat name would look like. He will then give you a final proof for you to approve.

Next is the printing process where he uses a proffessional grade plotter to cut out each color of 8 year, 3M vinyl graphics. Placing the graphics on top of each other to make a full color image or wording with optional shadows and images.

Boat Names can be shipped worldwide to any marina, business or home. Doug Rohloff the Boat Name Guy will insure delivery and help you step by step if you decide to DIY. (do it yourself) Otherwise will personally come to you to do the full installation!

The Boat Name Guy Serves the Florida’s Tampa Bay/Clearwater and Sarasota / Bradenton Area. Including: Clearwater, St. Petersburg, Tampa, New Port Richey, Sarasota, Bradenton and Palmetto.

 

The Boat Name Guy LLC Design Delivered Installed Tampa Clearwater © 2024 Frontier Theme